在操作过程中,请勿对混泥土搅拌车进行维修或润滑。
Do not repair or lubricate the concrete mixer during operation.
定期在每个注油嘴中添加黄油,每4小时润滑轴端密封油一次,每周排干一次。
Add butter to each oil filler regularly, lubricate the shaft end sealing oil every 4 hours and drain it once a week.
使用混泥土搅拌车后,根据需要在每个润滑点添加所需的润滑剂。
After using the concrete mixer, add the required lubricant at each lubrication point as required.
混泥土搅拌车减速器的齿轮和轴承通过齿轮旋转将油分散到油箱的内壁,并流入轴承进行润滑。变速箱油位保持在燃油表的两条线之间。油位过高或过低都会导致每个组件的温度升高,润滑不良,功率损耗增加以及机器故障。
The gear and bearing of the reducer of the concrete mixer disperse the oil to the inner wall of the oil tank through gear rotation and flow into the bearing for lubrication. The transmission oil level is maintained between the two lines on the fuel gauge. Too high or too low oil level will lead to the temperature rise of each component, poor lubrication, increased power loss and machine failure.
用混泥土搅拌车选择的润滑剂不得具有特定的粘度和粘度,温度特性,低凝固点,良好的氧化稳定性,机械杂质和湿气,耐腐蚀,耐磨材料,其质量指标符合标准。
The lubricant selected by the concrete mixer shall not have specific viscosity and viscosity, temperature characteristics, low freezing point, good oxidation stability, mechanical impurities and moisture, corrosion-resistant and wear-resistant materials, and its quality indicators shall meet the national standards.
自动上料搅拌车在使用的时候应该做好防护,因为它是长期暴露在外面,所以使需要做好防护的,根据我们的经验我们可以了解到漆面出现损伤的情况是非常多的,就让我们来做一个简单介绍:
The automatic feeding mixer truck should be well protected when in use, because it is exposed to the outside for a long time, so it needs to be well protected. According to our experience, we can understand that there are many cases of paint damage. Let's give a brief introduction:
自动上料搅拌车
Automatic feeding mixer
一、浅划痕:由于摩擦及日常护理不当,漆面出现轻微的划痕,但并未露出底漆,这种划痕在阳光下比较明显。一般通过抛光方法去除。
1、 Shallow scratch: due to improper friction and daily care, there are slight scratches on the paint surface, but the primer is not exposed. This kind of scratch is more obvious in the sun. Usually removed by polishing.
二、褪色:大气中的油烟和污染物是造成车漆变色、褪色的主要原因。褪色与氧化不同,发生褪色时,车漆会出现不均匀的色差。中、轻度的褪色可用研磨、抛光治理,严重时重新喷漆。
2、 Fading: oil fume and pollutants in the atmosphere are the main reasons for the discoloration and fading of car paint. Fading is different from oxidation. When fading occurs, the paint will have uneven color difference. Moderate and mild discoloration can be treated by grinding and polishing, and repaint in case of serious discoloration.
三、水痕纹:水痕纹是水滴蒸发后留下的痕迹,呈环状。氧化、常用洗涤灵清洗的车容易染上水痕。
3、 Water mark: water mark is the mark left by the evaporation of water droplets, which is circular. Cars that are oxidized and commonly cleaned with detergent are easy to get water marks.
四、漆面氧化:在太阳紫外线的照射下,漆膜会不断向空气中蒸发油份以达到保护自身的作用,长时间就会导致漆面油分的过分散失。漆面的亮度都大打折扣,使漆面慢慢发白,形成氧化层,缩短了车漆的寿命,氧化严重的话可以通过研磨和抛光来处理。
4、 Paint oxidation: under the sun's ultraviolet radiation, the paint film will continuously evaporate oil into the air to protect itself, which will lead to excessive loss of paint oil for a long time. The brightness of the paint is greatly reduced, which makes the paint white slowly and forms an oxide layer, which shortens the service life of the car paint. If the oxidation is serious, it can be treated by grinding and polishing.
五、蚀痕:蚀痕是面状磨蚀。昆虫、鸟粪、树汁、焦油、沥青都有可能引起的蚀痕。轻微的蚀痕可用研磨抛光来。
5、 Etch marks: etch marks are surface abrasion. Insects, bird droppings, tree sap, tar and asphalt may cause corrosion marks. Slight corrosion marks can be solved by grinding and polishing.
以上就是自动上料搅拌车表面经常遇到的一些情况,希望大家啊要做好防护,定期的学习表面养护的知识,经做好防水处理,就会减少自动搅拌车
The above are some situations often encountered on the surface of automatic feeding mixer truck. I hope you should do a good job in protection, regularly learn the knowledge of surface maintenance, and reduce the number of automatic mixer truck after waterproof treatment
本文的精彩内容由自动搅拌一体车知识提供,本网站还有很多的精彩内容,更多的内容您可以点击进入:http://www.shanqijituan.cn我们有专门的客服为您解答问题
The wonderful contents of this article are provided by the knowledge of automatic mixer. There are many wonderful contents on this website. You can click to enter more contents: http://www.shanqijituan.cn We have special customer service to answer your questions