多功能搅拌车做底盘润滑是需要注意的地方有哪些？_ 行业动态_新闻资讯_自动搅拌一体车_自动搅拌一体机

站内搜索

新闻资讯

公司新闻行业动态

热点

自动上料平口搅拌机多种方量可供选择

2022-12-23

混凝土自动上料搅拌车的功能有哪些？

2022-12-19

混凝土自动拌料车移动式可自行走户外施工

2022-12-16

自上料搅拌车企业这么多，买车的时候应该看哪方面？

2022-12-12

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

多功能搅拌车做底盘润滑是需要注意的地方有哪些？

所属分类：行业动态发布时间：2022-03-23 来源：http://www.shanqijituan.cn/ 浏览量：0

混凝土搅拌车底盘进行正确的润滑可以减少汽车零件的磨损，增加搅拌车零件的使用寿命，但是在实施润滑时应注意一下几点：1、正常使用情况下，按搅拌车厂家的保养周期进行润滑，环境恶劣情况下要适当缩短保养周期。

The correct lubrication of the chassis of concrete mixer truck can reduce the wear of automobile parts and increase the service life of mixer truck parts, but the following points should be paid attention to in the implementation of lubrication: 1. Under normal use, the lubrication should be carried out according to the maintenance cycle of mixer truck manufacturer, and the maintenance cycle should be appropriately shortened under bad environment.

2、要选用规定的润滑油。代用油料须性能接近，主要技术指标须保证，并且用代用油应时常检查，且缩短使用周期。

2. The specified lubricating oil shall be selected. The performance of the substitute oil must be close, the main technical indicators must be guaranteed, and the substitute oil should be checked frequently, and the service cycle should be shortened.

3、更换发动机机油时，要在热状态时进行，以保证油能放尽。放油时应注意检查机油颜色是否正常、机油有无异物，以便发现故障隐患。待油放尽后，放油螺栓上的异物，然后拧紧。

3. When changing the engine oil, it should be carried out in the hot state to ensure that the oil can be drained. When draining the oil, pay attention to check whether the oil color is normal and whether the oil has foreign matters, so as to find hidden troubles. After the oil is drained, remove the foreign matters on the oil drain bolt, and then tighten it.

4、进行润滑前，要清洁入口。润滑后要清洁零件表面，以免沾上尘土和污物5、更换上新机油滤芯，将新机油注入发动机到油尺上限。为防止在没有润滑油的情况下启动发动机，应使高压油泵处于断油位置时按启动按钮，空转一会儿后，再启动发动机，并低速运转。检查机油滤清器有无渗漏，停机后，检查并补充机油油面到油尺上。

4. Clean the inlet before lubrication. Clean the surface of the parts after lubrication to avoid dust and dirt. 5. Replace the filter element with new engine oil and inject the new engine oil to the upper limit of the dipstick. In order to prevent starting the engine without lubricating oil, press the start button when the high-pressure oil pump is in the oil cut-off position, idle for a while, then start the engine and run at low speed. Check the oil filter for leakage. After shutdown, check and replenish the oil level on the dipstick.

6、换机油滤芯：更换机油时，机油滤清器要同时更换，在密封垫上涂上一层薄薄的油，并且紧固滤清器。

6. Oil change filter element: when changing the oil, replace the oil filter at the same time, apply a thin layer of oil on the sealing gasket, and fasten the filter.

以上就是为大家介绍的有关多功能搅拌车的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.shanqijituan.cn/

The above is a detailed introduction to the multi-functional mixer truck. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.shanqijituan.cn/

上一页：自上料搅拌车制动系统的重要性下一页：如何节省自动上料车的成本？

热门产品 / HOT PRODUCT