自动搅拌一体机基本结构主要包括取力器、搅拌筒前后支架、减速机、液压系统、搅拌筒、操纵机构、清洗系统等。其工作原理:通过取力装置将汽车底盘的动力取出,并驱动液压系统的变量泵,把机械能转化为液压能传给定量马达,马达再驱动减速机,由减速机驱动搅拌装置,对混凝土进行搅拌。
The basic structure of automatic mixing machine mainly includes power take-off, front and rear support of mixing drum, reducer, hydraulic system, mixing drum, control mechanism, cleaning system, etc. Its working principle: the power of the automobile chassis is taken out by the power take-off device, and the variable pump of the hydraulic system is driven. The mechanical energy is converted into hydraulic energy and transmitted to the quantitative motor. The motor drives the reducer, and the reducer drives the mixing device to mix the concrete.
效率生产、生产一直各大企业比较重视的问题,在使用时节油的问题也受到部分客户的关注,小编今天来给大家分享一些省油的小技巧:
Efficiency production and energy-saving production have always been the issues that major enterprises attach great importance to. During the use of oil, some customers also pay close attention to the problem of oil. Today, I'd like to share some tips on fuel saving
一、车辆起步
1、 Vehicle start
车辆在起步时,可以大油门,充分发挥发动机的性能,让搅拌车以快的时间达到巡航车速,这样驾驶可以达到节油的目的。
When the vehicle starts, the accelerator can be increased to give full play to the performance of the engine, so that the mixer can reach the cruising speed in a fast time, so that the purpose of fuel saving can be achieved.
二、平路行驶
2、 Driving on a level road
1、平路行驶时,尽量在一条车道上行驶,减少来回变换车道的情况发生,有利于节油。
1. When driving on a flat road, try to drive in one lane to reduce the occurrence of lane change back and forth, which is conducive to fuel saving.
2、如果与其他车辆结伴而行,切勿采用跟车的方式,可以各自行驶,约定好相聚点。往往在后面跟车的车辆油耗会高于前车。
2. If you travel with other vehicles, do not use the way of following the car. You can drive separately and agree on the meeting point. Usually, the fuel consumption of the car following is higher than that of the car in front.
3、控制好发动机转速,不同发动机,控制转速不一致。
3. Control the engine speed, different engines, control speed is not consistent.
4、在平路行驶时,尽量保持油门开度的稳定,油门在30%左右即可,切忌油门忽高忽低。
4. When driving on a flat road, try to keep the throttle opening stable. The throttle should be about 30%. Never change the throttle from high to low.
三、车辆爬坡
3、 Vehicle climbing
1、搅拌车在爬坡的时候,坚持小坡冲,大坡稳的原则。
1. When the mixer truck climbs the slope, it adheres to the principle of small slope flushing and large slope stability.
2、坡度小路段的时候可以采用冲坡的方式,车辆提前加速,让车辆具有足够的惯性行驶到坡顶。
2. When the slope is small, the way of flushing can be adopted. The vehicle can accelerate ahead of time, so that the vehicle has enough inertia to drive to the top of the slope.
4、在车辆即将到达坡顶时,如果前方是下坡,可以减小油门开度,利用车辆的惯性到达坡顶,切勿在即将到达坡顶时增挡,这时完全可以利用下坡的惯性进行增速,减少不必要的燃油消耗。
4. When the vehicle is about to reach the top of the slope, if the front is downhill, you can reduce the throttle opening, use the vehicle's inertia to reach the top of the slope, do not increase gear when you are about to reach the top of the slope. At this time, you can use the inertia of the downhill to increase speed and reduce unnecessary fuel consumption.
油耗其实是不可避免的,我们只能通过一些小技巧减少自动上料搅拌机的油耗。
In fact, fuel consumption is inevitable. We can only reduce the fuel consumption of automatic charging mixer through some small skills.